Free on-site assessment
We inspect the foam with a boroscope inspection camera and moisture meter, identify open cell or closed cell foam, check for cavity wall bridging and timber rot, then give you a fixed written price. No charge, no obligation.
Licensed
Licensed & Bonded
Fully Insured
Insured & Bonded
24/7 Emergency
Same-Day Response
Warranty Backed
4+ Years Trusted in Clacton on Sea
What our dry ice blasting spray foam removal includes
Every job includes a free assessment, full site protection, dry ice blasting, debris removal, verification and documentation. We do not charge extra for photos or a written summary. If you need timber treatment or new insulation, we quote that separately before starting.
Full site protection
We sheet up floors, seal the loft hatch, isolate electrics and set up an air scrubber and industrial vacuum extractor. Our technicians wear PPE respirator and eye protection throughout. Your home stays clean.
Dry ice blasting removal
We use a professional dry ice blasting machine and dry ice pellets to freeze and shatter the foam from rafters, purlins and roof decks. No water, no chemicals, no abrasive media. Typical loft takes three to five hours.
Debris removal and vacuum
All foam debris is bagged and removed from site. We vacuum the loft space, wipe down timbers and run the air scrubber to clear airborne particles. You get a clean, empty loft ready for inspection or new insulation.
Verification and photo pack
We photograph every rafter before and after, log moisture readings and provide a written summary. For mortgage lender spray foam removal cases, we include a method statement and photo pack you can hand to your broker or surveyor.
dry ice blasting spray foam removal in Clacton on Sea
dry ice blasting spray foam removal in Clacton on Sea uses compressed dry ice pellets fired at high velocity to freeze and shatter polyurethane foam. The foam embrittles at around -78C, then lifts cleanly from timber, brick and roof rafters. Unlike sand blasting equipment or a thermal lance, dry ice leaves no abrasive media and no water, so your loft insulation, vapour barrier and wiring stay dry. We pair the dry ice blasting machine with an industrial vacuum extractor and air scrubber to capture every fragment.
Clacton on Sea has a lot of older housing stock with loft insulation and cavity wall insulation that was topped up with spray foam in the 2000s and 2010s. That foam has now trapped moisture, causing condensation in loft spaces, timber rot from trapped moisture and, in many cases, mortgage refusal due to spray foam. If you are searching for dry ice blasting spray foam removal near me Clacton on Sea Essex, we cover Great Clacton, Holland-on-Sea and Jaywick with the same kit and the same fixed pricing.
What to expect from start to finish
We keep the process simple: assess, protect, remove, verify, hand back. Most lofts are done in a day. Larger roofs or commercial units may take two to three days. Here is exactly what happens when you book us.
01
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
02
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
03
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
04
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Tools and methods we use
Tools & Equipment
dry ice blasting machine
Fires dry ice pellets at high velocity to freeze and shatter spray foam. Our machines run at adjustable pressure so we can switch between delicate rafters and stubborn closed cell foam.
industrial vacuum extractor
Captures foam debris and dust at the point of removal. We use H-class extractors with long hoses so the loft stays clear while we work.
air scrubber
Filters airborne particles during and after blasting. Keeps the rest of your home clean and protects our technicians.
boroscope inspection camera
Lets us inspect behind rafters, under roof decks and inside cavities without cutting holes. We use it during assessment and again after removal to verify timber condition.
moisture meter
Measures timber moisture content before and after removal. We log readings for every rafter so you have evidence for your lender or surveyor.
PPE respirator
Full-face respirators and eye protection for every technician. Dry ice blasting produces fine particles, and we do not cut corners on safety.
reciprocating saw and oscillating multi-tool
Used only where foam has bonded to fixings or where access panels need opening. We keep cutting to a minimum to protect timbers.
Methods & Standards
Cryogenic blasting
Dry ice pellets at -78C freeze the foam, which becomes brittle and releases from the substrate. No water, no chemicals, no abrasive media. This is our primary method for all spray foam types.
PAS 2035 retrofit principles
We follow PAS 2035 guidance for insulation removal and replacement. That means assessing ventilation, moisture and thermal bridging before recommending new insulation or vapour barrier.
BBA certification guidance
Where replacement insulation is specified, we work to BBA certification requirements so the new system is warranty-compliant and acceptable to lenders.
TrustMark-aligned documentation
Our photo packs and method statements follow TrustMark-aligned formats. Lenders and surveyors recognise the format, which speeds up mortgage release.
When to book dry ice blasting spray foam removal
01
Your mortgage lender has flagged spray foam in the loft and set a deadline before they will release funds.
What we do: We prioritise lender deadline jobs. A free assessment within 48 hours, removal booked the same week, and a full photo pack and method statement sent to your broker within 24 hours of completion.
→ Most lenders accept our documentation and release the mortgage. You get a clean loft and the paperwork you need, without chasing contractors.
02
You have condensation in the loft and suspect the spray foam is trapping moisture against the roof timbers.
What we do: We assess with a moisture meter and boroscope inspection camera, then remove the foam with dry ice blasting. We check every rafter and advise on ventilation and vapour barrier repairs.
→ Moisture readings return to normal within days. Timber rot is caught early and treated before it becomes structural.
03
You are selling a property in Clacton on Sea and the buyer's survey has highlighted spray foam insulation.
What we do: We provide a fast, fixed-price removal with before-and-after photos and a written summary. The buyer's surveyor can inspect the clean rafters, and we can speak to them directly if needed.
→ The sale proceeds without a price reduction for foam removal. You have documented evidence that the roof structure is sound and dry.
04
You own a commercial unit or warehouse in Essex with spray foam on a large roof area.
What we do: We use dry ice blasting machines with extended hoses and mobile vacuum units to clear large areas fast. We work outside your operating hours to avoid disruption.
→ The roof is cleared, documented and ready for new insulation or a warranty-backed roof coating. Minimal downtime for your business.
How dry ice blasting spray foam removal works in Clacton on Sea
Clacton on Sea has a mix of Victorian terraces, 1930s semis and post-war bungalows. Many were insulated with spray foam between 2005 and 2015, often under government schemes. That foam has now aged, and we see the same problems repeatedly: condensation in loft, damp from spray foam insulation and mortgage refusal due to spray foam. The coastal climate adds to it. Salt air and driving rain from the seafront mean roof timbers already work hard, and trapped moisture accelerates timber rot from trapped moisture. We use dry ice blasting because it does not add water to an already damp roof space. For dry ice spray foam removal Clacton on Sea near me enquiries, we cover everything from Clacton Town Centre to Jaywick and St Osyth. If you need cryogenic spray foam removal Clacton on Sea 24/7, call 03335672543. Typical 2026 pricing for a 3-bed semi loft is 1,500 to 2,200, with most jobs completed in a single day.
Neighborhoods We Serve
-
Great Clacton
Lots of 1930s semis with loft spray foam installed under older grant schemes. Access is usually good, and most lofts are cleared in a day.
-
Holland-on-Sea
Bungalows and chalets close to the seafront. Salt air and damp mean timber rot from trapped moisture is more common here, so we check every rafter.
-
Jaywick
Many properties have non-standard construction and older insulation. We assess carefully before quoting and use low-pressure blasting where timbers are soft.
-
Clacton Town Centre
Victorian terraces with tight loft access. We use compact dry ice blasting equipment and long vacuum hoses to work in confined spaces.
-
St Osyth
A mix of period cottages and modern builds. Period properties often need timber treatment alongside foam removal, which we quote separately.
Local Conditions We Plan For
-
Coastal salt air and driving rain
Roof timbers in Clacton on Sea already face high moisture loads. Dry ice blasting avoids adding water, which reduces the risk of rot after removal.
-
Older housing stock with grant-funded foam
Foam installed under older schemes is often thicker and more brittle. It blasts off quickly, but we always verify timber moisture afterwards.
-
Tight loft access in terraces
We use compact blasting equipment and flexible hoses so we can work in narrow lofts without removing roof tiles or cutting extra hatches.
-
Lender-driven deadlines
Mortgage valuations often stall on spray foam. We prioritise these jobs and provide documentation within 24 hours of completion.
Mortgage rescue on a Great Clacton semi
Problems our dry ice blasting spray foam removal solves
Spray foam that was installed years ago is now causing damp, rot and mortgage problems across Clacton on Sea. Here are the most common issues we fix, and what happens if they are left alone.
Problem
Mortgage refusal due to spray foam
Lenders often decline mortgages when spray foam is present because they cannot verify the roof structure. Without removal, you cannot sell or remortgage the property.
Our Fix
We remove the foam with dry ice blasting, verify the timbers and provide a photo pack and method statement. Most lenders accept our documentation and release funds within two to three weeks of removal.
Problem
Damp from spray foam insulation
Spray foam traps moisture against timbers and roof decks. Over time that causes condensation in loft, timber rot from trapped moisture and reduced property value.
Our Fix
Dry ice blasting removes the foam without adding water. We then check moisture levels with a moisture meter and advise on ventilation and vapour barrier repairs to stop the damp returning.
Problem
Roof rafter damage
Scraping or grinding foam can gouge softwood rafters. Damaged rafters may need structural repair, which adds cost and delays a sale.
Our Fix
Dry ice blasting freezes the foam so it releases without cutting into the timber. We inspect every rafter with a boroscope inspection camera and flag any damage before we finish.
Problem
Cavity wall bridging
Foam injected into cavity walls can bridge the gap and transfer damp to inner walls. That leads to damp patches, mould and failed building survey results.
Our Fix
We carry out cavity wall spray foam removal using dry ice blasting and vacuum extraction. We clear the cavity, restore airflow and provide evidence for your surveyor or lender.
Why dry ice blasting beats other removal methods
Dry ice blasting removes spray foam without water, chemicals or abrasive media. That means less mess, less risk to your timbers and a faster return to a mortgageable property. Here is what that looks like on a typical Clacton on Sea job.
-
No water damage
Traditional removal can soak timbers and insulation. Dry ice blasting spray foam removal in Clacton on Sea is a dry process, so your roof rafters, loft insulation and vapour barrier stay dry. On a typical 3-bed semi we remove foam from 12 rafters in under four hours with zero moisture left behind.
-
No chemicals or media
We do not use solvents, and we do not leave sand or grit in your loft. The dry ice pellets sublimate back to gas, and our industrial vacuum extractor captures the foam debris. That means no secondary clean-up and no chemical smell in your home.
-
Protects timbers
Scraping or grinding foam can gouge softwood rafters. Dry ice blasting foam removal Clacton on Sea freezes the foam so it releases without cutting into the timber. We follow up with a boroscope inspection camera and moisture meter to confirm the wood is sound and dry.
-
Mortgage-friendly finish
Lenders want spray foam gone and the roof structure verified. Our dry ice cleaning spray foam Clacton on Sea process leaves rafters clean enough for a surveyor to inspect. We provide before-and-after photos and a written method statement you can hand to your lender or broker.
Accredited, insured and documented
Licensed & Certified
- CHAS Accreditation — issued by CHAS
- SafeContractor Accreditation — issued by SafeContractor
- TrustMark-aligned methods — issued by TrustMark
- PAS 2035 retrofit training — issued by British Standards Institution
Verified Reviews
Google ★★★★★4.9
Spray Foam Removal Clacton on Sea cleared our loft in a day. The dry ice blasting left no mess and they gave us a photo pack for the lender. Mortgage went through two weeks later. Would recommend to anyone in Clacton.
Google ★★★★★5.0
We had closed cell foam and condensation problems. They removed it without soaking the timbers and found a small patch of rot. Quoted separately for treatment. Honest, tidy and on time.
Checkatrade ★★★★★4.8
Used them on a warehouse roof in Essex. Worked nights so we could stay open. Cleared 600 square metres of foam and provided photos for our warranty claim. Professional outfit.
Google ★★★★★4.9
Booked after a surveyor flagged spray foam. They assessed on Tuesday and removed on Thursday. Fixed price, no extras. The loft was cleaner than when they arrived. Highly recommend.
Four years removing spray foam in Essex
Spray Foam Removal Clacton on Sea has been removing spray foam since 2022. In that time we have cleared open cell and closed cell foam from lofts, roofs, cavity walls and commercial units across Clacton on Sea and the surrounding Essex villages. Our technicians are trained in cryogenic blasting, PAS 2035 retrofit principles and safe working at height. We carry CHAS and SafeContractor accreditation and use TrustMark-aligned methods. Every job is insured, and we work to BBA certification guidance where insulation systems are involved.
- Four years of dedicated spray foam removal across Clacton on Sea and Essex.
- CHAS and SafeContractor accredited, with TrustMark-aligned working methods.
- Trained in PAS 2035 retrofit standards and cryogenic blasting safety.
- Experienced with Isothane, Soudal, Fischer, Recticel, Icynene, Lapolla, BASF and Dow foam products.
- Full public liability insurance and a 1-year workmanship warranty on every removal.
Frequently Asked Questions
Real answers to the questions we hear most often from local homeowners and property managers.
How much does dry ice blasting spray foam removal cost in Clacton on Sea?
Most residential lofts in Clacton on Sea cost between 1,200 and 3,500 in 2026, depending on roof size and foam thickness. A typical 3-bed semi with open cell spray foam runs 1,500 to 2,200. Closed cell foam, cavity wall spray foam removal or commercial units cost more. We give a fixed written price after a free assessment.
Is dry ice spray foam removal safe in Clacton on Sea Essex?
Yes. Dry ice blasting is a dry, chemical-free process. The pellets sublimate to CO2 gas, and we run an air scrubber and industrial vacuum extractor throughout. Our technicians wear PPE respirator and eye protection. We isolate electrics and protect surfaces before we start. The loft is safe to re-enter as soon as we finish.
Is dry ice blasting spray foam removal near me available in Clacton on Sea?
We cover all Clacton on Sea neighbourhoods, including Clacton Town Centre, Great Clacton, Holland-on-Sea, Jaywick, St Osyth, Point Clear and Little Clacton. We also travel to Thorpe-le-Soken, Weeley and Frinton Road. Same-week assessments are standard, and we offer 24/7 call-out for urgent lender deadlines.
How does dry ice blasting remove spray foam in Clacton on Sea?
We fire dry ice pellets at around -78C through a dry ice blasting machine. The foam freezes, becomes brittle and shatters off the timber. An industrial vacuum extractor captures the debris immediately. We then check each rafter with a moisture meter and boroscope inspection camera. A typical loft takes three to five hours.
Related Services
Spray Foam Removal near me
If you need spray foam removal near me in Clacton on Sea, our dry ice blasting service is the cleanest option. We remove open cell and closed cell foam from lofts, roofs and cavity walls with no water or chemicals, leaving timbers ready for survey.
View Spray Foam Removal near mesame day Spray Foam Removal
For urgent mortgage deadlines or surveyor visits, we offer same day Spray Foam Removal in Clacton on Sea where access allows. Call before 10am and we can often have a crew on site the same afternoon with the dry ice blasting machine.
View same day Spray Foam Removal24/7 Spray Foam Removal
Our 24/7 Spray Foam Removal line covers Clacton on Sea and Essex for emergency call-outs. If a lender has set a deadline or a survey has flagged spray foam, call 03335672543 any time and we will arrange the earliest possible dry ice blasting slot.
View 24/7 Spray Foam RemovalResidential Spray Foam Removal
Most of our dry ice blasting spray foam removal in Clacton on Sea is residential. We clear lofts, attics, roof rafters and cavity walls in houses, bungalows and flats, with full protection for your floors, wiring and insulation.
View Residential Spray Foam RemovalCommercial Spray Foam Removal
We handle commercial spray foam removal for warehouses, offices and agricultural buildings across Essex. Dry ice blasting is ideal for large roof areas because it is fast, dry and produces minimal waste. We work around your operating hours.
View Commercial Spray Foam Removalloft spray foam removal
Loft spray foam removal is our most common job. We remove foam from rafters, purlins and roof decks, then verify timber moisture. Dry ice blasting avoids the water damage that steam or chemical methods cause in loft insulation.
View loft spray foam removalTalk to our Clacton team
Call us on 0333 567 2543 between 08:00 and 18:00, Monday to Friday, and you will speak to someone who has actually been up a Clacton loft this month. Out of hours, leave a message and we will call you back first thing. For surveys, quotes and documentation requests, email [email protected] and we will reply the same working day.
Spray Foam Removal Clacton on Sea
-
Phone
03335672543 -
Address
72-78 Rosemary Rd, Clacton on Sea CO15 1TZ, UK, Clacton on Sea, Essex
-
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available